
![]() |
C Melody Saxophone Forum / Mouthpieces Reeds and Ligatures / Can my mouthpiece be fixed?
NOTICE: Beginning July 10th, 2008, this message board service will no longer be active or available for use.
Next 20 Messages
Eric
User ID: 0791694
Aug 28th 7:23 PM
First: I'm far from a technical expert, so please excuse my stupidity. I play a Conn "Wolverine" stencil, generally using an Aquilasax mouthpiece, which plays great. I also have a Goldbeck mouthpiece, sounds good but has a narrow tip rail which I think tends to squeek a bit (at least with my technique). Here's my question: I've found a vintage Conn mouthpiece with wide side rails, but the tip has been worn- it's no longer properly flat & makes playing tricky. Can this be built up to restore the original contour, or should it be refaced- and would this open it up too much? (I'm clueless)
bruce bailey
User ID: 9690803
Aug 29th 12:05 AM
It would probably need a refacing. There are some refacers out there who can give you a better idea. Mojo is one and now Wofe Tanninbaum in Ft. Lauderdale (Wolfe Tayne, BARI) is at it again.
Captain Beeflat
User ID: 1738604
Aug 29th 5:07 AM
Why not buy a modern mouthpiece and save yourself all the hassle...and eliminate the stuffy sound. If your horn is a C Melody then the dedicated Aquilasax mouthpiece comes highly recommended and is not expensive.
Jazzbug1
User ID: 0735934
Aug 29th 7:03 AM
I would think the Aquilasax mouthpiece is the best bet. Those old Conns have a huge tubby sounding chamber. If you want to get rid of the Goldbeck, put it on Ebay. It will fetch a good price if it is a C melody. I use a Goldbeck (so did Rudy Wiedoeft) and find it very nice. It has a classic sound with a metallic edge. The chamber looks narrower than the big plastic ones of the 20s. Good luck.
Jim B
User ID: 2783734
Aug 29th 10:03 AM
I did this to my chipped mouthpiece with the same problem. You buy some epoxy which has two parts---the exoxy base and a fixer mix. After mixing up you apply to the problem areas. Once hardened you do some careful filing. The epoxy costs about $5USA in any hardware store.Also many music stores (the repair section) have a stash of sax mouthp0ieces---- probably some Conn C melody mouthpieces among them. Cost if you find any is usually under $20USA--- whatever you can talk them into.
Eric
User ID: 0791694
Aug 29th 5:38 PM
Well, first I DO have an Aquilasax mouthpiece & its great. The Goldbeck hard rubber I can take or leave, mostly it sits in the case as a backup. Someone may have worked on the tip rail as it's narrowe4r than the Aquilasax. As to the conn, I just want to see if it can be put into usable shape to try it out. I'm not certain about the epoxy plan- there aren't chips, the outer edge of the tip rail is now beveled away from the chamber, so although the reed closes against the inner edge of the rail the tip of the redd is unsupported & buzzes. I paid $20.00 plus shipping, so I don't want to just toss it (figuratively speaking). BTW- I'm going to haul out my ancient Buffet-Crampon wood C mel mouthpiece & give it a go.
Eric
User ID: 0791694
Aug 29th 5:41 PM
I should add that after reading some old posts, everybody raves about Goldbeck mouthpieces, but they're talking about metal. Mine is standard hard rubber.
Jazzbug1
User ID: 0735934
Aug 30th 6:35 AM
Eric-- I have never seen nor heard of a hard rubber Goldbeck. I had a 1934 catalog which only listed metal examples. Your item is quite unusual. I did the epoxy once. It works well. Perhaps you can build up the area, then carefully sand it to the point that it sounds right. The best epoxy I ever used is J and B weld. I have even repaired small engine blocks with it. Big box stores or Automotive stores carry it. Good luck.
Eric
User ID: 2170744
Aug 30th 9:02 AM
It has A. Goldbeck in script. Down at the bottom of the table it's marked FRANCE on one side and X on the other.
Jazzbug1
User ID: 0735934
Aug 30th 11:42 AM
The metal Goldbecks were made in Chicago and later bought out by Kaspar (later 30s?). As best as I can figure, your Goldbeck was made by a French maker to be distributed by dealers who sold the Goldbeck line. I know that at least in the early 1930s, Selmer US was a distributor of Goldbeck mouthpieces. The X refers to an opening size or table design. Sounds interesting.
Eric
User ID: 2170744
Aug 30th 2:15 PM
It sounds like I should hold onto it a while. Regarding my tryout of the wood C mel mouthpiece (Unaccountably I've never used it before) Maybe because of the wood, or Buffet-Crampon being primarily a builder of clarinets, it seemed to make my sax sound more like a clarinet- a narrower timbre with less bite to it, but not dead. It was rather nice in fact- might be useful for ensemble work. I really should get the Evette-Schaeffer-Buffet-Crampon rebuilt, though it won't be cheap.
Eric
User ID: 0791694
Sep 2nd 7:09 PM
Just a thought regarding my Conn mouthpiece- yes it's probably a piece of junk, but I'd still like to tinker with it. Problem is, the material I want to replace is at the very outer edge of the tip rail & I don't think it will hold on. What if I cover the entire facing with a thin metal foil (maybe copper foil- certainly not household tinfoil)& build up the area under that? I've seen hard rubber mouthpieces with metal insert facings.
Captain Beeflat
User ID: 1738604
Sep 3rd 5:01 AM
Eric.
For the metal insert you will require, for starters, a Spark Erosion Machine and a CNC miller...most domestic workshops are not so equipped. Why not save yourself a load of grief and chuck the mouthpiece over a hedge.
alan (uk)
User ID: 0651814
Sep 3rd 6:41 AM
Eric - if only the end result (the sound I mean) was worth all that effort. And that much time and effort would probably relate to half re-padding a C-Mel (hint...)
Jim B
User ID: 9440113
Sep 3rd 7:33 AM
Eric----Epoxy can be used to build up a mouthpiece not "just for chips". Try using the stuff. Under $5 the price is right. Build it up and file it down. You can follow the advice of alan(uk) and Captain Beeflat or buy the Conn company OR try the epoxy. I think you can, I think you can.
Eric
User ID: 0791694
Sep 3rd 2:05 PM
I'll try a bit of the above and Captain, I was just planning a thin metal foil for the surface of the facing, not a whole metal chamber, so I'm not going to need a milling machine.......
alan (uk)
User ID: 0651814
Sep 3rd 3:20 PM
Eric, if you go ahead, you're going to need to bond the foil to the facing, so epoxy could do that - and usefully fill in any un-eveness (as you'd want the surface to be dead flat. Thin foil might not be strong or rigid enough.
I was a bit surprised that you mentioned copper - I can't think of anything that is put in the mouth that's uncoated copper, although I don't think it's toxic, as weren't some old cooking pots and jelly moulds made of copper ? But I would imagine copper would patinate/corrode relatively easily - certainly copper tubing does, when exposed to air and dampness !
Eric
User ID: 0791694
Sep 3rd 6:33 PM
True, I was wondering about copper, but I don't think I'd have this particular piece in my mouth long and often enough to be toxic- and I'd clean it after use so corrosion shouldn't be a problem. My other more choices would be brass foil (no real diference & it has a sharper taste) and aluminium foil. Perhaps gold leaf, but that would wear through in no time & its support I want. I know this is putting effort into an item not worth it, but c'mon- haven't you ever been in a situation where the process turns out to be more than the result? You've never worked over a junk horn instead of breaking it up for parts?
Anyhow, after all this talk I'll probably do nothing at all.
Captain Beeflat
User ID: 1738604
Sep 4th 4:27 AM
Eric.
For reasons that I fail to understand, you seem determined to rebuild that stuffy old Conn...why not file down the rails to provide a substantial keying surface, build them up with epoxy or glass fibre resin, then carefully re profile them. The curve will be very similar to that assumed by a reed with finger pressure applied to it's tip...similar to the curve of a long bow, which was called tillering.
Frankly though, it appears that you have too much time on your hands. :-)
alan (uk)
User ID: 0651814
Sep 4th 8:46 AM
Eric - some of my best projects still remain "in my head" - witness the petrified forest of driftwood in my back yard waiting to be turned into works of art......
Bb - that 'reed curve/profile' is a good explanation - so logical I'd never thought about it that way before...
Next 20 Messages