Swirve.com Links: Swirve.com   Free Email   Games   Fantasy Sports   E-Cards   Movies   Horoscopes   Freebies   Web Search


NOTICE: Beginning July 10th, 2008, this message board service will no longer be active or available for use.

C Melody Saxophone Forum / C-Soprano Saxophones / G# Key on Conn C-Sopranos

WW2
User ID: 9955583
Nov 22nd 12:26 PM
This weekend I was playing my C-Soprano. It is a Wurlitzer made by Conn in 1922 ( see http://mysite.verizon.net/res8o1o8/soprano.html ).

Many of the keys were sticking or sluggish so I decided to take apart the entire upper stack, the palm keys, and the bell keys to clean the tone holes and pads. I also cleaned and lubricated all the rods and pivot screws. The lower stack was accessible so I also oiled it, but did not remove it.

After re-assembly I noticed some problems with the G# pinky key and the low C# key. Upon close examination, I realized the the G# Pinky Pad Key seems to be too big for this saxophone. The notch for the C# key is about 6mm (1/4 inch) too low and interferes with the full opening of the C# key. The G# key opens fine. Also, I check the spring on the G# key and it seem to be 5 to 10 mm too long. It seems as if the key is the G# key from a Bb-Soprano put on this as a replacement.

If anyone owns a Conn or Conn Stencil C-Soprano from about 1922, could you measure this key for me? I would like to know:

- overall length of the key,
- distance from the pinky pad end of the key to the start of the notch for the C# key clearance,
- the width and depth of the C# notch,
- And the length of the spring.

To do these measurements you will need to take the key off of the saxophone, but this is simple. Please note the way it is attached so you can get everything back properly. Also take the opportunity to oil the rod.

Thanks for your help!
Bill Hall
User ID: 0436494
Nov 23rd 10:19 AM
I have a 1925 Conn. Do you think that's close enough? Also, how accurate do the measurements need to be? I can also do pictures if that will help.
WW2
User ID: 9955583
Nov 23rd 11:55 AM
Hopefully the 1925 will be close enough. Pictures would be great! Actually, with decent pictures showing how the C#, G# and G# lever all interact would be worth a lot of measurements.

As for accuracy, to witin 1/8" (about 3mm) should be close enough.

Thanks!
Bill Hall
User ID: 0436494
Nov 23rd 3:13 PM
Okay, I'll try to get it done this evening, Wade. I'm in Texas, so I've got a couple of hours on you. Is wwalker@gte.net a good email address for you?
WW2
User ID: 9955583
Nov 23rd 4:30 PM
Bill;

My new email address is:

wwalkerjr@verizon.net

since I upgraded to DSL from 56K. Unfortunately verizon did not allow me to keep my old user name and email.
Bill Hall
User ID: 0436494
Nov 24th 7:57 AM
Did you get my email last night?
WW2
User ID: 9955583
Nov 24th 12:55 PM
Thanks Bill. It seems that the 1925 model has an entirely different G# key than my 1922.
Doc Frazier
User ID: 9377263
Nov 24th 10:16 PM
Wade, could you send me some pics of your key and let me compare them to my Pan American C that I have here?
Yours in CHRIST, Doc

www.JandJWoodwinds.com
Doc Frazier
User ID: 9377263
Nov 24th 10:17 PM
Wade, could you send me some pics of your key and let me compare them to my Pan American C that I have here?
Yours in CHRIST, Doc

www.JandJWoodwinds.com
JandJ_Woodwinds@bellsouth.net
Bill Hall
User ID: 8673953
Nov 25th 1:03 AM
Strange that they linked G#/C# on the 1922 model but didn't on the 1925 model. Maybe they were making it cheaper so they could lower the price or something.
WW2
User ID: 8318753
Nov 28th 12:37 PM
I finally got a couple of pictures of my G# key posted to my site. They are at:

http://mysite.verizon.net/res8o1o8/csop/G-Sharp%20Mounted.JPG

and

http://mysite.verizon.net/res8o1o8/csop/G-sharp%20Dismounted.JPG

If you have a Conn or Conn Stencil with this type of G# key, I would appreciate it if you could give me the measurements in my original post on this thread.

Thanks Bill Hall for the pictures of yours. Too bad they updated the keys layout by then.